|
|
SolRxTM
E-Series Multidirectional Phototherapy
ExpandableTM 2-Bulb Full Body Panel System
6-Foot Models: E720M(Master) & E720A(Add-On)
Control System & Other Components
|
Technical Data
More Photos
|
|
MASTER Device Components:
At the top of the MASTER device, a
digital countdown timer
provides timing control to the second, and has a maximum time setting of 20:00 minutes:seconds.
A particularly useful feature of this timer is that
it always remembers the last time setting,
even if power is removed from the device for a long period of time.
This means that you will always have your last treatment time setting for reference.
The time is set by simply pressing the up or down arrow keys,
and the lights are turned on/off by pressing the START/STOP button.
The lights turn off automatically when the timer counts down to 00:00.
The timer's red display is easily seen through the patient goggles supplied.
The timer does NOT require prescription refills from your physician.
The timer's output relay carries a UL-508 [NEMA-410] ten Amp (10Amp) "Ballast" rating
and has been tested by Solarc in a 10-bulb (1000 watt) device for over 30,000 on-off cycles -
that's 2 treatments per day for 41 years.
The timer is top quality, UL/ULc certified, and made in the USA.
A
keyed switchlock
is the main power disconnect for the device.
By removing and hiding the key, unauthorized use can be prevented.
This is an important feature, especially if kids are around,
because mistaking this medical UVB device for a UVA tanning machine can have serious consequences.
Turning the switchlock off disconnects power to the entire device,
which saves the energy consumed by the timer when it is in standby mode.
The
labels
are made from Lexan® and will not fade.
|
|
On top of the MASTER device endcap, there are several other important components:
1.
The black
fused power inlet
is the connection point for the detachable power supply cable (3 meters long),
AND the location of the electrical safety fuse drawer.
If more than four (4) ADD-ON devices are connected, the fuse will blow.
A spare 10-amp fuse is located in the fuse drawer.
2.
The two black
receptacles
are the connection points for the left-side and right-side ADD-ON devices.
Screw-on dust-caps are provided for use when an ADD-ON device cable is not connected to the receptacle.
3.
The two silver coloured
upper mounting brackets
are permanently connected to the back of the MASTER device and are simply rotated into position when needed,
as shown by the lower picture.
The hole locations are marked and the supplied drywall anchors and screws fastened.
Note that ALL of the weight of the device is resting on the floor,
so these mounting brackets are basically only to keep the unit from falling over.
The mounting brackets therefore do NOT have to be mounted to a wall stud.
ADD-ON devices do not have mounting brackets,
but they could be installed if ever needed.
4.
The
serial number label
includes the device model number, serial number, bulb part number,
ultraviolet waveband type (such as UVB-Narrowband or UVB-Broadband),
and electrical information such as voltage(volts-ac) and current(amps) ratings.
|
The 3-meter long detachable power supply cord (supplied)
simply plugs into the power inlet on the top of the MASTER device,
and is routed down the side to a standard household 15-amp, 120 volt, 3-prong (grounded) wall outlet.
There are no special electrical requirements.
|
If ADD-ON devices are to be connected,
the two LOWER mounting brackets on the MASTER should be fastened to the wall,
typically to the baseboard using the two screws provided.
These brackets prevent the bottom of the MASTER device from being pulled away from the wall when ADD-ON devices are repositioned.
|
The LOWER mounting brackets are permanently attached to the bottom of the MASTER device and simply rotated into position when needed.
The bottom of the MASTER device has the same white plastic ski as ADD-ON devices,
to provide a large footprint to prevent damaging carpet,
and if the MASTER is ever used as a moveable device in one of the many other larger
assembly configurations.
|
The MASTER device can also be mounted in a corner,
however corner-mounting does not give enough room on the sides for connection of any ADD-ON devices.
|
To corner-mount the MASTER device,
easily identified diamond-shaped holes are provided in the sheet metal as shown.
Simply mark the hole locations on the wall,
screw in the wall inserts, and fasten.
ADD-ON devices also have these holes.
This picture is one of the many illustrations from the
Users Manual.
|
The MASTER device by itself has very substantial UVB output from its two 100-watt bulbs (200-watts total).
|
|
ADD-ON Device Components:
On top of the ADD-ON device,
there is no timer or switchlock, but there are several other components:
A.
The black
connection cable
is permanently attached to the ADD-ON device and connected to the receptacle on top of an adjacent device;
which could be either a MASTER device as in this picture, or an ADD-ON device.
B.
The black
receptacle
is open and waiting for the connection cable from the next left side device.
The tethered dust-cap is shown installed.
The MASTER device also has an available receptacle.
There is always an open receptacle on the two outermost devices.
C.
ADD-ON devices also have a
serial number label
that includes the device model number, serial number, bulb part number, ultraviolet waveband type,
and electrical information such as voltage(volts-ac) and current(amps) ratings.
D.
The hinge lugs (ears) are connected using the supplied
hinge hardware,
which is a simple 1/4"-20 machine-screw and nylon-insert-locknut;
one set each for the top and bottom hinges;
easily installed in just a few minutes.
|
This picture shows the fastening of the lower hinge point,
and below it the white plastic "skis" resting on the carpet.
The device positions can be locked by fully tightening the fasteners.
|
The hard white plastic "skis" on the bottom of all devices are very slippery and smooth.
They allow remarkably easy positioning of the devices.
|
With the connection of just one ADD-ON device to a MASTER,
the number of bulbs doubles and a powerful 400-watt multidirectional assembly is created.
|
Solarc Systems Inc., 1515 Snow Valley Road, Minesing (Barrie), Ontario, Canada L0L 1Y3
Toll Free: 1.866.813.3357 Tel: 705.739.8279 Fax 705.739.9684
|
|
|
|
|
